The controller make and model should be included. Generate signals which cause the aircraft to climb, dive, or perform coordinated The connecting system parts such as the sensor switch. Maintain a predetermined altitude, rate of climb, or descent. The units transmitting output information signals to automatically Typical partsĪre resistor, circuit board, capacitor, or power supply, etc.
#Ata chapter engnies series
The major components such as computer, servo,Īnd controller are to be filed in the specific JASC 2200 series code.įor reports pertaining to the autopilot computer only. Typical parts are yaw damper,Ĭable, switch, sensor, relay, etc. Used for controlling attitude and direction. When there is insufficient information to file in a more specific JASC 2200įor reports of miscellaneous parts associated with the autopilot system Includes those units and componentsĬontrolling direction, heading, attitude, altitude, and speed. The units and components that furnish a means of automaticallyĬontrolling flight of the aircraft. Typical parts areīag, sock, filter, moisture separator, etc. Temperature of the air in the cabin and relays a signal to the indicator.įor reports of system parts that control humidity. Indicates the air temperature in the cabin.įor reports of the sensors and associated circuitry sensing the Typical entry would only reference the "control unit" if specific part numbersįor reports of the indicators, lamps and associated circuitry which Typical partsĪre control valves, thermal sensing devices, switches, amplifiers, and wiring.įor reports of the parts within the cabin temperature control unit. The units and circuitry other than the control unit which are used forĬontrolling the temperature of the air in the cockpit and cabin. Typical partsĪre flow valve, relay, condenser, ram air sensor, heat exchanger, cooling The units and systems supplying cooled air to the cockpit or cabin.ĭoes not include the temperature control and indicating system. Typical parts are fuel pump, filter, plumbing, circuitry, Includes the heat source (heater), controlling aspects, and temperature The units and systems supplying heated air to the cockpit or cabin. Typical parts are pressure switch, transducer, etc.
![ata chapter engnies ata chapter engnies](https://image.slidesharecdn.com/traduccional1rodriguezgonzalezraul-copia-141108152800-conversion-gate01/95/traduccion-ata-100-7072t-15-638.jpg)
The units and systems which measure differential pressure and transmitĪ signal. The defective part should be identified by the part name and part numberįor reports of the cabin pressurization system, pressure indicators,įor reports of outflow/dump valves and associated parts such as Typical parts areĪmplifier, switch, electrical connector, etc.įor the reports pertaining to the controller units only and not for the Typical parts are bearing, bushing, motor, etc.įor reports of miscellaneous system components or parts other than theĬontroller, indicator, sensor, regulator, or outflow valves. Which distributes air within the confine for comfort or equipment cooling. Typical parts are equipment rack cooling systems, ozone converters, scoops,ĭucting, inlets, check valves, wiring, etc.įor reports pertaining to the fan/blower including associated motor That are a part of the temperature control, pressurization, or the distributionįan. The system used to induct and distribute air. Indicating systems related to the compressors, wiring, etc. Specific defective part by name and part number. Related entries should include the component manufacturer's make, model, and the Reported problems with the compressor unit and not the associated system. The system and its controls supplying compressed air to the cabin.
![ata chapter engnies ata chapter engnies](https://cf.ppt-online.org/files1/slide/u/uCXrO7iBWoZdkmReFhJKqUxQsj1fa2DA5GVS49/slide-10.jpg)
![ata chapter engnies ata chapter engnies](https://s2.manualzz.com/store/data/044482462_1-141e635623b956e460109a5b11a15a98-595x842.png)
Ventilate areas of the fuselage within the pressure vessel. Heating, cooling, moisture controlling, filtering, and treating the air used to The general instructions are not applicable to any particularįor miscellaneous parts that cannot be associated with specific airĬonditioning, pressurization, or distribution codes.Įtc., with no reference to the specific using system on the incoming report.Īlso, for those units and components furnishing a means of pressurizing, The general instructions are not applicable to any particular system.įor reports indicating a problem relating to aviation lubricating oil.įor reports which indicate a problem with any type of hydraulic fluid.įor reports indicating a problem with any type of engine coolant used Text = the "closed and locked" decal is missing from the main passenger entrance door).įor reports indicating a problem relating to any type of aviation fuel. (Example: Item = placard location = entrance door part condition = missing. Such information should be extracted from the text and entered in the proper data fields. The location of the item is essential for a meaningful report. The report should include the system or component involved. For reports on all placards, decals, and markings installed by the manufacturer including those required by government regulations.